Gradall Forklift Parts

Gradall Forklift Parts - The Gradall excavator was the creation of two brothers Koop and ray Ferwerda. The excavator was created In the 1940's through WWII, when there was a shortage of labourers. The brothers faced the problems of a depleted workforce because of the war. As partners in their Cleveland, Ohio construction company called Ferwerda-Werba-Ferwerda they lacked the available workers so as to perform the delicate job of grading and finishing on their interstate projects. The Ferwerda brothers chose to make an equipment which would save their business by making the slope grading task less manual, easier and more efficient.

Their very first design prototype was a device with two beams set on a rotating platform which was affixed over a used truck. A telescopic cylinder moved the beams forward and backward that allowed the fixed blade at the end of the beams to push or pull dirt. Before long improving the very first design, the brothers made a triangular boom so as to add more strength. Additionally, they added a tilt cylinder which let the boom turn 45 degrees in both directions. A cylinder was positioned at the rear of the boom, powering a long push rod to allow the machine to be outfitted with either a blade or a bucket attachment.

Gradall launched in 1992, with the introduction of the new XL Series hydraulics, the most innovative adjustment in their equipment since their creation. This new system of top-of-the-line hydraulics allowed the Gradall excavator to provide high productivity and comparable power to the more traditional excavators. The XL Series ended the initial Gradall equipment power drawn from low pressure hydraulics and gear pumps. These conventional systems effectively handled grading and finishing work but had a difficult time competing for high productivity work.

The new XL Series Gradall excavators proved a significant increase in their digging and lifting ability. These models were manufactured with a piston pump, high-pressure hydraulics system that showed huge improvements in boom and bucket breakout forces. The XL Series hydraulics system was even developed with a load-sensing capability. Traditional excavators utilize an operator to be able to pick a working-mode; where the Gradall system can automatically adjust the hydraulic power intended for the work at hand. This makes the operator's general work easier and likewise conserves fuel at the same time.

As soon as their XL Series hydraulics came onto the market, Gradall was basically thrust into the highly competitive market of machinery meant to deal with excavation, demolition, pavement removal as well as various industrial tasks. Marketability was further improved with their telescoping boom because of its exclusive ability to work in low overhead areas and to better position attachments.

Click to Download the pdf

Forklift Parts

Differentials for Forklifts

Forklift Differential - A mechanical machine which can transmit torque and rotation via three shafts is referred to as a differential. At times but not all the time the differential will utilize gears and will operate in two ways: in automobiles, it provides two outputs and receives one input. The other way a differential operates is to put together two...

More

---

Parts for Platform Scissor Lift

Platform Scissor Lift Parts - Scissor platform lifts may perform by pneumatic, hydraulic or mechanical means. The scissor part is the folding arm which is capable of folding in on itself or lengthening to be able to lower or raise the table on top. This arm can be extended to various heights so as to accomplish specific tasks. Scissor hoists...

More

---

Carriage Mounted Spreader Bar

Carriage Mounted Spreader Bars - As the name implies, this mast has 3 parts. The outside part mounts firmly to the lift truck. The next intermediate part telescopes within the outside part. The innermost part telescopes inside of the middle section. The internal section and the intermediate part both elevate as the lift cylinders extend. Once again in this model,...

More

---

Crane Hooks

Crane Hook - The Hoisting Hook could help alter whichever simple lift truck into an overhead lifting jack by utilizing a safety chain in order to affix it to the lift truck. To be able to lock this accessory to the lift truck carriage the safety chain utilizes a snap hook which locks to the center fork openings. This Hoisting...

More

---

Forklift Engine

Forklift Engine - Also known as a motor, the engine is a device which could convert energy into a functional mechanical motion. Whenever a motor transforms heat energy into motion it is normally referred to as an engine. The engine can come in numerous kinds like the internal and external combustion engine. An internal combustion engine typically burns a fuel...

More

---

Forklift Pinions

Forklift Pinion - The main axis, called the king pin, is found in the steering machine of a lift truck. The first design was a steel pin wherein the movable steerable wheel was mounted to the suspension. Able to freely turn on a single axis, it limited the levels of freedom of motion of the remainder of the front suspension....

More

---

Remanufactured Forklift Part

Remanufactured Forklift Parts - Lift trucks are quite costly pieces of equipment for the reason that a brand new electric lift truck model can cost anywhere from eighteen thousand to twenty five thousand, for a five thousand pound machinery. Moreover, some thousands of dollars would have to be invested in a battery charger and battery. The same internal combustion lift...

More

---

Forklift Mast Rollers

Mast Rollers - The lift truck mast is an essential part of the lift truck's structure. These forklifts or also called lift truck vehicles are industrial equipment used so as to lift and transfer merchandise. The vertical assembly responsible for raising or lowering a load is known as the mast. A forklift mast consists of interlocking rails which provide lateral...

More

---